SCP 1000 Macerator Pump

Diagram and Parts List

SCP 1000 Parts Breakdown

Fig. Index	Name	Qty Ass’y	STDN PART#
1	Shaft Key	1	22201
2	Coupling Flange, 5/8”	1	22202
3	3/8-16 x 1” SS Hex Head Cap Screw	4	N/A
5-Apr	Not Used
6	¼”-28 x ¾” Set Screw (Hex)	4	22206
7	¼”-28 Hex Nut	4	22207
8	Bearing Cap	1	22208
9	Retaining Ring	1	22209
10	Shaft	1	22210
11	Seal Plate (Replaces 22211, ALL except Rev. 4) (Replaces 22211, ALL except Rev. 3)	1	22251 22267
12	Bearing Frame (replaces 22212 ALL) Note 2	1	22266
13	Gasket	1	22265
14	5/16”-18 x 1 ½” Hex Head Cap Screw	6	22214
15	¼”-20 x ½” Socket Head Cap Screw	3	22215
16	Not Used
17	Axial Cutter	1	22217
18	5/16”-18 x 1” Hex Head Cap Screw	4	22218
19	Radial Cutter	1	22219
20	Impeller Washer	1	22220
21	¼”-20 x 5/8” Flat Head Screw	1	22221
22	Suction Head	1	22222
23	Cutter Ring	1	22223
24	O-Ring	1	22224
25	Spring Pin	1	22225
26	Impeller, 17-4 (replaces 22226 ALL)	1	22253
27	Volute (Replaces 22227 ALL except Rev. 3) (Rev. 3)	1	22268 22252
28	Not Used
29	O-Ring	1	22229
30	Mechanical Seal Kit (Seal Head and Seal Seat)	1	22200-2
31	¼” NPT Hex Head Plug	4	22231
32	O-Ring, Bearing Cap	1	22232

33	Ball Bearing Obsolete See 48
34	¼��-20 x 1” Socket Head Cap Screw	2	22234
35	Bearing Locknut	1	22235
36	Oil Seal	1	22236
37	Discharge Nozzle	1	22237
38	Coupling Flange, 7/8”	1	22238
39	Coupling Sleeve	1	22239
40-42	Not Used
43	Bushing, Shaft	1	22243
44	Sight Glass, Oil Cavity, Brass (SCP 1000)	1	22244
45	¾” NPT Brass Plug (SCP-1000)	2	22245
46	Vent Breather	1	22246
47	O-ring, Shaft (Part of seal kit 22200)	1	22247
48	Ball Bearing (Horizontal & Vertical Mount Replaces 22233 ALL)	1	22248
49	Discharge Nozzle O-Ring	1	22249
50	Rebuild Kit	1	22250-2
51-53	Not Used
54	Seal Flush Nozzle (Not Shown) (Rev.3 ONLY)	1	22254
55-58	Not Used
59	Motor, Electric, 2 HP (Multi-Voltage) Motor, Electric, 1HP (Multi-Voltage)	1	21460 21430
60	Oil, Macerator, 1 Qt.	1	22260
61	Gauge, Oil Level (Vertical Mount Only)	1	22261 & 22262
●All parts listed are interchangeable with all models of macerator pumps sold except where noted. ●If Bearing Frame #22212 (integral discharge nozzle) is replaced with Bearing Frame # 22266 (removable discharge nozzle), then the Volute # 22253 and the Discharge nozzle # 22237 must also be replaced. ●Internal Sleeve Bushing tool #22263 and Mechanical Seal tool #22264 are required when replacing the Mechanical Seal.

California ◊ Florida ◊ Shanghai ◊ Germany

Lagos Nigeria ◊ Valparaiso Chile ◊ Dubai UAE

Trusted Since 1985

Pacific Marine & Industrial is
a registered service mark of:

Quality Pacific Manufacturing, Inc.